Indium Wire

Maria Durham, Indium’s new Technical Specialist in Semiconductor and Advanced Assembly Materials, has been doing some research on indium lead (In/Pb) solder alloys. We chatted about her findings this week. 

 [Andy C. Mackie: ACM] Which indium/lead solder alloys are most common, and what are their properties?

[Maria Durham: MD] Firstly, the use of lead-(Pb-)containing solders in some soldering applications is restricted due to local environmental and RoHS compliance, but there are still many applications where they are  allowed. Many military, aerospace, and industrial equipment uses, as well as many applications related to vehicles, are exempt. The table below shows the most common indium/lead (In/Pb) alloys (pink) and their properties, sorted by liquidus temperature; the higher of the two melting points (solidus and liquidus) seen for non-eutectic alloys. In blue are three comparison materials.

Indalloy 205 is the most commonly used, probably because it has the closest liquidus temperature to the tin/lead eutectic (183°C), 63Sn/37Pb (Indalloy 106). This means it can be reflowed using a standard Sn/Pb eutectic profile. The next most common alloys that are used are Indalloy7, 204, and 206.  Besides the melting range, indium has comparable thermal and electrical conductivity to standard materials.

[ACM] What makes indium-lead (In/Pb) solders so attractive, and why have we seen a recent resurgence in their usage?

 [MD] One main attraction to using indium/lead (In/Pb) solder alloys in soldering to precious metal surfaces is that, unlike tin-containing solders, they do not leach gold. That is, gold does not dissolve in them to any appreciable extent. During discussions at Semicon West in 2011, one of our California customers reported going through 8 simulated reflows with Indalloy 205 in contact with a gold surface with no loss of joint strength and no joint embrittlement. That is pretty impressive. Note that embrittlement is often caused by gold-intermetallic formation. It has been noted that even at 250°C, 50In/50Pb dissolves Au at a rate 13 times slower than it does into 63Sn/37Pb, although this, of course, is a kinetic, not a solubility limit, study.

The higher melting Indalloy 164 (92.5Pb/5In/2.5Ag) has the lowest coefficient of thermal expansion (CTE) of all of the In/Pb solders and is able to withstand the higher temperature excursions that can be seen in step-soldering type applications (where a very high melting solder is used to form the first joint, followed by a next lowest melting alloy, and so on). This is seen in applications such as power electronics assembly, where the first step solder is often used for die-attach either as a solder paste, wire, or preform. The high melting point helps the solder withstand the operational temperatures associated with under-the-hood electronics, in applications such as engine control modules, where Indalloy 151 (92.5Pb/5Sn/2.5Ag) or Indalloy 163 (95.5Pb/2Sn/2.5Ag) are most commonly used. In/Pb solder is excellent on very rigid structures such as ceramic-to-metal or ceramic-to-ceramic. The desired solidus / liquidus temperature range can be adjusted by changing the indium:lead ratio, making it very easy to “dial in” the alloy to a specific reflow process.

Another attraction to using In/Pb solders is that they exhibit good fatigue resistance in thermal cycling from -55°C to 125°C.  In testing, the 50In50Pb solder joint fatigue life is about 100 times greater than that for 63Sn/37Pb.

 [ACM] What fluxes are used in these applications, and how are they formulated differently?

 [MD] The fluxes most compatible with the lower melting point (<200°C) indium-containing solders are NC-SMQ-80 (solder paste) or the lower-tack TacFlux® 012 (suitable for use with wire, preforms, and spheres). These are no-clean fluxes, specifically formulated for lower temperature reflow.  Under appropriate low temperature reflow these fluxes leave behind benign residues that do not need to be cleaned off (“no-clean” flux), although they are often cleaned off in most practical applications, usually to ensure reliable wirebonds absent of flux spatter.

 To learn more, please contact us.

 Cheers!  Andy

Reducing the surface oxides of Nitinol is just the first step in getting a good solder joint with this versatile medical assembly material.

Next you have to choose the right solder alloy.  You will probably want to stay away from anything containing lead, cadmium, or antimony, particularly in medical applications.  And you will want something with a high tensile strength.

The best choice is Indalloy #121 (96.5Sn 3.5Ag).  It has a tensile strength of 5,620 PSI and a melting temperature of 221C and is obviously lead-free.  It wets well to the cleaned Nitinol.

If you need a higher melting temperature solder (one that can withstand autoclave temperatures for example) you should consider Indalloy #182 (80Au 20Sn) which melts at 280C, has a tensile strength of 40,000 PSI, and has long been considered a highly reliable solder.  Additionally, this alloy is available in very fine diameter solder wires to minimize waste.

Soldering temperatures should be 25C to 50C above the liquidus temperature of whichever solder you use and proper cleaning should be always be performed afterwards.

Contact us at medical@indium.com for more information about soldering for medical devices or visit our web site at www.indium.com/medical

Carol

Eric Bastow recently wrote about using our Indalloy Flux #2 for soldering to Nitinol.  He did many tests and wrote an Application Note called Soldering to Nitinol.

Fort Wayne Metals, a leading supplier of medical wire (including Nitinol) also did a test on various fluxes as they relate to break load (maximum load before the joint breaks.

The fluxes tested included:

• Indalloy Flux #2 and Flux #3
• Indalloy Flux #5RMA; #5R; #5RA
• Indalloy Flux #4R
• Flux #400 (no longer commercially available)

The #5 series and the #4R were found to not be strong enough to clean off the tenacious oxides formed on Nitinol. Therefore, they didn't enable the solder to wet the surface properly.

Flux #2 and Flux#3 gave the best results (of the fluxes tested for break load) since they removed more of the oxides and allowed for a stronger solder bond.

Want to know more about soldering to this important medical material?  You can contact Eric Bastow directly at ebastow@indium.com or email us at medical@indium.com. 

Carol Gowans

cgowans@indium.com

Anyone who has used wave soldering to assemble PCBs knows about that chunky layer of metal that collects on the smooth surface of the molten solder. This is solder dross; it is composed of oxidized metals and impurities that collect as the molten solder contacts the air and manufacturing environment. This happens regardless of alloy and is a normal part of the process, often consuming up to 50% of the bar solder added to the solder pot. In the past, this dross was collected as waste and disposed of, but solder dross is more than 90% valuable metal. This value should be recovered.

Nowadays, typically, this dross is collected and returned to a metals supplier for recycling. Indium Corporation now offers two programs for recycling solder dross. The first program involves simply sending back dross waste in return for a portion of the metal value as a credit. The second option involves sending back dross, which is converted to bar solder (within the original spec) and returned, with you paying only a fee for processing. When dross arrives, regardless of which program is chosen, it is electrolytically refined and the pure metals are recovered and converted back into usable bar solder. Often, this reclaimed/recycled metal has a better purity than virgin metal.

Dross is not the only form of solder that can be recycled. For instance, when changing to a different alloy in a wave soldering process, the entire solder pot will need to be emptied. The old alloy can be collected and recycled, lowering the amount of capital necessary to switch alloys. Bar solder and wire that have not been used within the shelf life can also be recycled to get back some of their value.

Contact me if you want to discuss this.

• It remains malleable at cryogenic temperatures
• It is soft and pliable so it fills imperfections in mating metal surfaces and creates a hermetic seal

Today I received an interesting email that could be useful for my readers. Here goes:

“Dear Jim,

I saw your recent blog. I am in the process of prototyping a photovoltaic application. I am aware that Indium Corporation has a lead-free alternative for tabbing and bus wire. Can you comment on why the photovoltaic industry, specifically in the US, has not adopted this standard as a better non-toxic solution and what Indium Corporation has done to promote this alternative? I look forward to hearing your point of view!

Best Regards,”

That’s definitely an important question, what an ice breaker! This was my response:

“First of all, thank you for reading the blog and thank you for the thoughtful question.

What many people do not realize, is that there are actually a few different types of lead-free alternatives for cell tabbing. The 3 most common alloys for tabbing ribbon are :

• 96.5Sn/3.5Ag
• 57Bi/42Sn/1Ag
• 58Bi/42Sn

Here are the main reasons that people stick with Sn/Pb based tabbing ribbon coatings:

• Sn/Pb and Sn/Pb/Ag have been extensively proven with many different module designs  
  
• Indium (the metal) based alloys are quite expensive compared to Sn/Pb based alloys
• Sn/Ag melts at a higher temperature range, causing greater expansion of the base copper (and therefore greater coefficient of thermal expansion mismatches).
• Some people fear the melting point of Bi/Sn and Bi/Sn/Ag may be too low for their subsequent processes (such as lamination)

The key point I’d like to note is that there are companies currently using each one of these alternative, and finding them feasible in regards to cost and reliability. We promote the use of these alloys - I would personally like to see the 57Bi/42Sn/1Ag alloy take over the market. I like to see my customers making good modules and feeling good about the materials they use too!

All the best,

          ~Jim”

Later on in the day we discussed the technical aspects of using lead-free alloys and settled on Bi/Sn/Ag and GS-5454 as the go-to materials. It was great to have this conversation with someone focused on conscious material selection and eager to learn more about lead-free options.

What are your thoughts?

At the time of writing, the price of silver (Ag) was approaching the USD$50/tr.oz. (Troy ounce) level, and threatening to go higher. With 1 Troy ounce being 31.1grams, this makes the cost of pure silver ingot close to USD$1.60/gram.

Image from goldsilveroz.com

Materials costs are therefore a major consideration for anyone using silver in any form. Naturally, we are now seeing a few Power Semiconductor packaging houses evaluating the possibility of moving away from silver-filled epoxies for die-attach. The alternatives they are considering include the adoption of solder paste (or solder in some other form: wire / ribbon / preforms) versus a silver-filled epoxy.

Here are some thoughts on the Power Semiconductor assembly pros and cons, based on using solder paste as an alternative to silver-filled epoxies.

Good news (+)

+   Reduced materials costs
+   Improved pot-life / shelf-life *
+   Improved high temperature thermal-cycling
+   Strong, metallurgical joint formed between leadframe (substrate) / joining material / die
+   Improved thermal conductivity
+   Faster throughput (more units per hour, UPH)**
+   Easy clean-up ***
+   Does not wick onto NiPd surface to cause poor wire bondability

 * Although it is true that solder pastes are stored under refrigerated conditions, they do not require the -40C storage that is typical of silver-filled epoxies. 

 ** The dispense of solder paste is very rapid and can be done using multi-dot dispense heads. It undergoes rapid temperature reflow, versus the slow cure needed for metal-filled epoxies, which can be up to typically 1-3 hours, depending on the volume of silver epoxy.

 *** Because the solder paste flux does not cure like a polymeric material,  tubing and other conduits for the solder paste are easily cleaned out using common solvents, or can be simply purged with flux.


  ==================

Bad news (-)

-   Capital costs #
-   Adoption time / new process learning ##
-   Needs a solderable die surface
-   Voiding increase ####

 # The main cost-drivers here are:

- Reflow: Specialty reflow equipment is required for high temperature solders, such as
Heller or BTU reflow ovens

- Cleaning: If wirebonding is required after the reflow process, standard cleaning equipment and cleaning chemistry (aqueous or solvent-based) will be needed to remove flux residues

- Gas: Forming gas (H2/N2) or simple nitrogen may be needed to assist reflow.

Note that increasingly, for clip-bonding (non-wirebonding) applications using the new ultralow residue solder paste Indium9.32, even cleaning may not be needed, as the residue has been found to be compatible with compatible with a number of molding compounds in the industry.

 ## By partnering with a company like Indium Corporation with many years of experience in die-attach soldering, the ramp-up time can be significantly reduced.

 ### A solderable surface is usually a sequence of Ti / Ni / (Ag or Au) plated layers. The thickness of the silver (Ag) or gold (Au) precious metal layer is usually limited to 100nm (0.1microns). Compare this to a standard silver-epoxy bond line thickness (BLT) of 0.5-2mils (12-50microns).

 #### Acceptable voiding of less than 5% of the total die area is fairly easily achieved with good quality substrates and die-finishes.

  ==================

In closing, I am indebted to my friend and colleague Sehar Samiappan (Indium Corporation Area Technical Manager - South East Asia) for his insights.

Contact me to discuss this further.

Cheers!   Andy

The week of March 14th Indium Corporation will be exhibiting at the MD&M (Medical Design & Manufacturing) show in Orlando, Florida.  Actually it is one of many MD&M shows held throughout the country.

We have attended previous shows as visitors but this will be our first as an exhibitor.  We will be showcasing our Flux #2 and lead-free solders for soldering to Nitinol.  Eric Bastow recently wrote a blog post on using Flux #2 and either 96.5Sn 3.5Ag or 80Au 20Sn for this application.

Flux #2 cleans off the very tenacious oxides that form on the Nitinol, giving it a clean surface to solder to.  We will be providing further details and samples of the 96.5Sn 3.5Ag in wire form at the show.  You can also request a sample of the Flux #2 by giving us your contact details.  Stop by and see us at Booth 248-250.

Or you can contact Eric Bastow by email at ebastow@indium.com or me by email at cgowans@indium.com.

Jon major recently joined the Indium Corporation as a Product Manager for Solar back-end assembly products. I greeted him with this impromptu interview.

Jim: First of all Jon, welcome. It’s great to have you as a new addition to the team!

Jon: Thank you Jim – it’s an exciting time to be at Indium Corporation and a fantastic time to be a part of the growing solar industry. I am extremely enthusiastic about my new position and am looking forward to making a positive contribution to the solar industry.

Jim: I noticed it didn’t take you long to get up to speed. Your time in Silicon Valley must have helped.

Jon: Coming from the electronics industry with a focus on product development, new product introduction, manufacturing, and external partner management, I am excited that my past experiences can contribute both to the industry and to Indium Corporation. After joining Indium only a few weeks ago, not only am I getting used to Upstate NY weather, but I have been immersing myself in solar with the goal of gaining a comprehensive understanding of:

•       Both rigid and thin-film technologies

•       Technology trends

•       Global and regional markets (EU, China, US, North America)

•       Solar supply chain (Silicon, wafers, cells, module, equipment, inverters, integrators)

•       Equipment manufacturers, contract manufacturers, and how we can collaborate with them to move the industry forward

•       Our products and pricing

•       Our current and future customers

•       Our short and long term opportunities

•       Our competition

•       Our roadmap

•       Our strengths, weaknesses, and threats

•       Our manufacturing capabilities and our QA process

•       Our sales channels, value proposition, key differentiators

•       All Indium processes

Jim: I know you've got solar products on your mind. Let our readers know a little bit more about your role here at Indium?

Jon: As a Solar Backend Product Manager I will focus (officially) on the business development and growth of Indium’s Solar Back End product offerings.  Now that sounds great but what does it actually mean? I could cut and paste my official job description but I prefer to explain it in my own words. As I think about the first part of that statement, “business development and growth…”, I see my role as:

–      Know the market, the customers, the product, and the competition

–      Develop relationships with the Indium team, reps, partners, equipment manufacturers, and, of course, customers

–      Write valuable data sheets, publications, and sales literature

–      Listen to our customers' needs and provide solutions

–      Manage schedules and orders with minimal surprises

–      Build cross-functional collaboration (sales, distribution, marketing, engineering, R&D, QA, production, management)

–      Never let down partners or customers

–      Support all functions of the organization, both internal and external

–      Deliver above & beyond commitments

–      Make great bets – on technology, customers, and opportunities

–      Understand the product life-cycle

–      Ship high quality, consistent product

The second part of that statement “..of Indium’s Solar Back End product offerings” is fairly straightforward. Of course this means I will focus on Indium’s current back end products (tabbing ribbon, bus ribbon, metallization paste (or as I prefer to call it – “grid ink”), flux and flux cored wire). With a product development background, this also means I have an opportunity to work with customers, partners, and R&D to develop and bring new products to market that will advance the module assembly industry – very exciting for me personally.

Ultimately, I think of my role as both building awareness of Indium’s products and superior technical support available to our customers as well as helping to shape our growing industry.

Jim: Okay Jon, you’ve had a while to settle in and get familiar with our Solar Team’s past and present – what are you planning for the future of module assembly?

Jon: Regarding the future of module assembly it’s a bit early to know for sure but I am excited about our low-temperature bismuth-containing alloys. These low temperature, lead-free, bismuth-containing alloys reduce the soldering process temperatures, thus reducing thermal stresses. I’m also working with the Indium production team to further reduce our tabbing and bus ribbon yield strength. A lower yield strength will reduce mechanical stress on cells during the assembly process. This is crucial to minimizing the possibility of microcracks and cell breakage during the solar module assembly process.

In closing, having lived in California for the last 10 years, I am not 100% familiar with our Upstate New York climate, and especially not all the snow shoveling. I see in my future a solar powered driveway heater!

Jon can be reached at jmajor@indium.com

最近小忙，少讀書了，也少和大家分享了；不過工作之餘，翻看了一下《A Seat at The Table》一書，覺得裏面有些道理也蠻有啓發的。比如説此書中一直圍繞這個主題來展開了論述“Today, the only thing your customer cares about is value.”

就這個觀點，再對照一下Indium公司的兩個主要系列產品：

²       電路板組裝焊接材料(Solder Materials):  這裡也要分產品而論。對於技術含量較高，工藝使用要求較多的焊錫膏(Solder Paste)材料，重視成品可靠性的客戶們會更多的關注產品帶來的“價值”。 如果只圖便宜的材料，但是用起來“錯漏百出”的，最後還是事倍功半：返工，復修，廢棄率高（特別是浪費貴的不能翻修的板子），產出率低，總體成本也自然高了。 對技術含量較低，工藝已經“模式化”的產品，像錫棒(Solder Bar)，錫綫(Solder Wire),  性价比會更關鍵……在目前日益高漲的金屬原材料市場中，Indium公司考慮到客戶們的成本壓力，也推出了性能可以和SAC305錫棒媲美的有成本優勢的Sn995錫棒。

²       半導體封裝材料(Semiconductor Materials):  整個半導體行業應該算是一個高成本，高投資，高回報（運營得好的話）的三高行業。半導體封裝材料也像是其中的經絡血脈吧，連接各個部分，讓整體最後順暢無阻的工作。半導體各個部分的材料都不便宜，設備更是不菲；對材料性能的表現要求和驗證都很嚴格，畢竟都投資那麽多，不能“功虧一簣”嘛。所以客戶們一般會十分重視產品的價值。 Indium 公司目前提供的半導體材料有：Wafer Flux, Wafer Paste, Micro Spheres, Flip-Chip Flux, Substrate Paste, Ball Attach Flux, Die-Attach Paste/Wire, PoP Fluxes, etc. 

Indium公司還為大家提供散熱界面材料(Thermal Interface Materials)，工程焊料(Engineering Solders)，薄膜光付太陽能板製造材料&太陽能板組裝焊接材料(PV Solar Materials)，和銦金屬及其化合物等。 這些材料使用在比較領先的應用中，新興行業，或是細分市場中，客戶們都十分重視產品和服務能給自己帶來的價值。

Cheers!  

Pic: Indium Corporation

PS: 前些日子看了中央4台的《第三屆漢語橋在華留學生漢語比賽》，感慨不已！除了感嘆這些留學生們對“那麽難”的漢語的精湛掌握，對中國文化和歷史的了解，甚至對中國的熱愛；更感慨的是，這些活動也説明了祖國的強大！現在越來越多的留學生們來中國學習，想進一步了解中國，和中國人民交流；中國話也在慢慢傳播到全世界！以前中國學子們苦讀英語，考TOFEL, 雅思，GRE什麽的；現在金髮碧眼的學生們也在場上比拼誰更了解我們的“四書五經”了，哈哈！

I’m really excited about a new option for those of us who are prototyping solar assemblies or evaluating new tabbing ribbon materials. I’ve been waiting for something like this – everything you need to solder solar cells together in one package. The turn around time is key too – you may recall an older post where I learned how quickly these materials shipped.

On the website where these kits are offered, the description reads:

“Tabbing ribbon kits come with everything you need to evaluate how Indium Corporation materials will work with your solar cells and assembly process. The kits can be used to:
- Evaluate which tabbing ribbon size is best for your design
- Determine which flux is best for your operation
- Experiment with new solder coating alloys
- Assemble a few solar panels”

The tabbing ribbon kits come in 3 flavors:

- Standard Sn/Pb/Ag (62Sn/36Pb/2Ag)

- Pb-Free (96Sn/4Ag)

- Low Temp Pb-Free (58Bi/42Sn)

I have a feeling the Low Temp Pb-Free kits are really going to be the most popular of the 3 that are offered though. Application temperature ranges will determine which kit to use, but all three versions of the kits are said to offer similar base copper sizes and tolerances:
“The ribbon itself is industry standard CDA 110 (99.9% Cu) core flat wire, coated with a precisely controlled layer of solder. Each ribbon is manufactured using our proprietary softening process so you can increase the yield of your stringing process.” Basically, this means that the softer tabbing ribbon will help eliminate the breakage of thinned cells during the heating/cooling cycle.

It also includes some matching bus ribbon to complete your panel build. If you’re trying to find the right flux, this kit serves dually as a flux evaluation kit as well. The kit is loaded with VOC-Free flux, rosin-based flux, and resin-based tabbing fluxes. I prefer GS-5454 as a flux for most tabbing operations, but you can see how the others stack up as well.

Let me know how you like the kit after you try it out!

~Jim

(jhisert@indium.com)

PS: 最近在做某大客戶的生意，其中有一個性格爽朗的活躍女工程師K引起了我的注意。她看樣子就像剛PhD畢業參加工作的女孩子。後來客戶中了解這位工程師的好友L告訴我，K其實已經30多嵗了；18嵗時在某囯嫁給了36嵗的男人，漂亡來美國這個異國它鄉，先後生下兩個孩子。因爲前夫對她不好，K忍無可忍終于離婚了，但是前夫一直以來不讓她有探望孩子的權利，更別説照料了。K在美國，先後讀完了本科，碩士和博士；現在在好公司有份好工作，並且每天都努力地工作著。現在K也有了一個相處4年多的穩定男朋友了……聼完K的故事，讓我肅然起敬。從K開懷的笑聲中，外人全然看不出來她有這種痛苦的過去! 一個不對困境地頭，對生活充滿了熱情，對未來充滿期望並為之奮鬥的可貴靈魂！

In the surface mount technology (SMT) electronics and semiconductor packaging industries, Indium Corporation has a reputation for offering custom solutions.  In the world of solar cell manufacturing, I hope that same status is obvious.  I feel custom solutions are even MORE important in emerging technology fields like CIGS cell manufacturing.  Being the leading global supplier of indium (the metal), and a supplier of unique solder alloy shape/size/tolerance forms, we are well equipped to offer you evaporation sources that are tailored to your application.  Sure, we can supply round shot, teardrop shot, wire, ingot, preforms, and various other bulk forms of solder to keep your evaporation chamber filled.  Did you know we can also make custom solder castings to fit your particular crucible?  The process is easy, let us know if you are interested!

(Just click here to get started)

Solderspheres or solder spheres, or even solder balls: whatever you call them, Indium Corporation has been making them for years and has rightly acquired the reputation for doing whatever it takes to meet our customers' unique needs.

Unique Alloys:

Hard to find alloys (like multipart alloys; low-melting alloys and even gold/tin (80Au/20Sn)) are our bread and butter. As "Indium Corporation" it should be no surprise that we lead the world in our ability to supply low-melting indium-alloy solder spheres, as well as other forms of these alloys, such as engineered solders or solder pastes.

Unique Quantities:

We don't want you to buy more than you absolutely need. If you just want 100 spheres, we can easily do that: if you want more - we can do that, too. But remember that, because each customer's need is unique, our prices may be higher than our competitors, especially for more standard alloys. Some customers also have unique inventory-control needs, so we work with many customers to ship on-demand by retaining a buffer stock of spheres here at Indium.

Unique Sizes:

Our current dimensional capabilities as of this writing are from 80microns to 0.062inches, or even bigger. Generally, the bigger the sphere - the less spherical it is (within the limits of surface tension and viscosity), and we can't control the laws of physics, so instances where a very large amount of solder is needed, a preform may have better dimensional control. Also, notice that we won't ask that you order in a specific unit of diameter measurement, like the mil or the micron or the millimeter: we're a global company - just tell us what you need.

Unique Packaging:

Often needed for more delicate alloy spheres, we can offer specialty overpacking that eliminates oxides from the atmosphere around the solder spheres, essentially stopping oxidation in its tracks. It's the same technique we use to package our soft solder die-attach (SSDA) wire: a technique that showed that the very reactive wire was still "as new" 3 years later. We also offer spheres in tape & reel packaging (see image) for 24mil, 35mil and 62mil diameter spheres.

Unique Tolerances:

Just as a case in point, a MEMS customer of ours had a need for a low-melting indium-alloy solder sphere with a tolerance of +/-5microns (+/-0.005mm) for a sphere with a 350micron diameter. That demands a tolerance of just over 1% - pretty demanding, but we did it.

Our standard tolerance is +/-1mil (1 thousandth of an inch, or 25.4microns), but as you can see, we have the capability to go to much tighter tolerances using three proprietary manufacturing techniques.

Other Needs:

We are also seeing people asking for doped-alloy spheres; low-alpha emission solder spheres and other things that we could never have dreamed of...

So please just let us know what you need. We'd be happy to help out, and if we can not do what you ask - we'll let you know why.

Cheers!  Andy

I mentioned in a previous a blog posting that the primary driver for halogen-free electronics is ostensibly environmental, but that the confusion about “which halogens and which molecules and what level?” has seemingly decoupled the laudable desire for an improved environment from the reality and made it more of a marketing tool. All this notwithstanding, there remain some instances where the performance of the final product itself can be directly impacted by the presence of halogens, usually as ionic halides. This is the reason why Indium Corporation recently developed what appears, at first glance, to be an odd combination: a high-Pb (high-lead) alloy halogen-free die-attach solder paste, Indium9.72-HF.

The halogen-related failure mode for die-attach solder pastes is the corrosion of wirebond pads on the topside of Power Semiconductor die which are soldered to the leadframe with halogen-containing solder paste. Many manufacturers producing high volumes of identical power devices may also use die-attach (sometimes called “soft solder die attach”, SSDA) wire to attach the die to the leadframes in a fluxless process, but many manufacturers prefer the inherent flexibility of a solder paste-based process for medium mix / medium volume applications.

Long term blog readers will recall that I did a posting on solderspatter (a.k.a. soldersplatter or soldersplash), and that it can be caused by bubbles of solvent vapor or moisture outgassing from solder paste deposits during reflow. In bursting, the tiny flux droplets or solder particles from the surface of the bubble can be propelled quite a distance (several feet). While solder on wirebond pads is clearly a failure from a reliability viewpoint, certain wirebond pad metallizations may also be subject to corrosion from flux. A poorly maintained reflow oven may also drip flux condensate (usually in the exit – cooling – zone), and this too can be a cause of organic materials on wirebond pads.

As long as the bondwire is gold, and wirebond pads are covered in a uniform layer of gold, there is no problem (as long as the flux residue is washed off) since gold is unreactive, even in corrosive environments. Aluminum (Al) or aluminum/silicon (Al/Si) bondpads, however, are potentially reactive. Halogenated materials, such as fluxes and overmolding compounds may react with them to either reduce the wirebond pull strength and/or increase the wirebond junction resistance, leading to localized heating and subsequent thermal-related joint failure. Even covalently-bonded (C-X, where X is a halogen) materials may dissociate at high temperatures: which is how the banned brominated flame retardants work, of course.

The biggest danger of halogenated flux corroding wirebond pads is when:

1/ Completed assemblies (between the reflow process and the cleaning process) are left for a long time before cleaning; particularly if they are exposed to high humidity (high %RH) before cleaning.

2/ The cleaning process is inadequate: either due to poor selection of the cleaning solution, or poor bath maintenance, or inadequate “scrubbing” energy being imparted to the surface to be cleaned, or simply if inadequate time is allowed for cleaning.

Note that even optimizing 1/ and 2/ may still lead to bondpad corrosion.

The Indium9.72-HF paste is available in both type 3 and 4 powder, in the standard high-Pb alloys, Indalloy 151 (92.5Pb/5Sn/2.5Ag) and Indalloy 163 (95.5/2Sn/2.5Ag), and for larger die that need a higher reliability joint, we also offer the Indalloy 164 (92.5Pb/5In/2.5Ag). A Product Datasheet is available for download, of course.

Cheers! Andy