Bismuth

Do you ever have a need for a "low temperature" solder (meaning an alloy that melts at less than 175C)?

You may have delicate components that cannot withstand standard reflow temperatures, or maybe you are looking to reduce costs by lowering the reflow temperature, or you may be step soldering.  Whatever your reason, there are two unique metals that are used extensively in low temperature solder alloys.

The first one I am sure you can guess: Indium.  The other one is Bismuth. While these two elements are used extensively in the over 100 alloys available in the 50C to 175C range, they couldn't be more different from each other.

Indium is a very soft, malleable metal and remains so even at cryogenic temperatures. It melts at 156C.  Bismuth, on the other hand, is very brittle, even at room temperature, and melts at 271C.  But both lend themselves very nicely to solder alloys that melt below 175C.

Let's look at the two most common alloys in these families.

The two alloys:

• 52In 48Sn (Indalloy #1E) Melts at 118C
• 58Bi 42Sn (Indalloy #281) Melts at 138C

What they have in common are:

• Both are lead-free
• Both are tin-based
• Both are eutectic (liquidus and solidus temperatures are the same, with no plastic range)
• Both can be made into a wide variety of solder forms and can be used in low temperature applications

But the indium-based alloy will give you better compensation of coefficient of thermal expansion (CTE) mismatch than the bismuth alloy.  The bismuth alloy has greater tensile strength but has a lower shear strength than the indium alloy and is generally not recommended in applications where the product has potential to be dropped (like cell phones).  The indium alloy will give you greater thermal conductivity than the bismuth, as well.  The bismuth will give you a cost advantage.

So, which alloy do you use?  Well, that depends on the metallizations you are working with and the environment in which your final product will be operating. For example, if you are soldering to two different surfaces that expand at different rates, then you will want to go with the indium alloy - to keep your solder joints from cracking.  But, there are a lot more considerations when choosing a low temperature solder, and we can help you sort through them.  Check out our Low Temperature Solder page on the web or contact us at AskUs@indium.com or contact me directly at cgowans@indium.com and we can answer your questions or put you in touch with one of our local experts to review your entire process for the best solution.

Let us help!

Carol Gowans

After the report by Isofoton regarding reliability testing of Bi-based alloys for tabbing ribbon, the world learned that Bi-based alloys could survive the lamination process and function in use. If you haven’t seen it yet, I consider this mandatory reading! Here is the info: B. Lalaguna, P.Sanchez-Friera, I.J. Bennett, L.J. Caballero, J. Alonso, “Evaluation of Bismuth-Based Solder Alloys for Low-Stress Interconnection of Industrial Crystalline Silicon PV Cells", 22^nd EU PVSEC, Milan, 2007Milan, 2007.

We all know the Bi based alloys like 57Bi/42Sn/1Ag and 58Bi/42Sn can be used in a standard module assembly process, but is there an advantage to using Bi/Sn or Bi/Sn/Ag when Sn/Pb and Sn/Pb/Ag alloys are so well known and trusted in the industry?

I’ll give you 3 benefits:

1)    1) Bi/Sn/Ag and Bi/Sn are Pb-Free

2)    2) Bi/Sn/Ag and Bi/Sn are low-temperature alloys, they allow you to lower your tabbing process temperatures

3)    3) When paired with the correct flux and metallization, these Bi alloys form a powerful bond without microcracks (due to the lower process temperature)

Below are results with SunTab^TM ribbon assembled on a Komax X series stringer and tested on a XYZTEC Condor 150-3 bond tester (provided by the respective companies).

You’ll probably notice the lack of y-axis scale – I’m not going to give away all the cool information that easily! Contact me at jhisert@indium.com to learn more.

上周是感恩节。根据美国的习惯，我们拷了一只火鸡Turkey来庆祝。

平时向客户们介绍我们公司的preform预成型焊片这一大产品系列时，我们经常会用这个有趣的故事：你们知道这个细条小圆柱形的焊片用在哪里吗？ 感恩节的火鸡里！其实是pop-up turkey timer。 在全美销售火鸡和火鸡测温器的厂家，都可以大量地使用我们这种低温合金的焊片。每年感恩节烤火鸡，大家会把timer插在火鸡里面，等火鸡里面也达到一定温度（熟了），在timer里面的低熔点合金(含有铋金属Bi/Bismuth)就会融化膨胀，使其里面的弹簧自动跳起来。

Bi58Sn42是一种很常用的无铅低温合金。它可以用在散热器heat sink/heat pipe的焊接上，也可以用在电路板的印刷焊接上。有些客户板子上的某些元部件有不能承受超过180⁰c 或是190⁰c(Sn63Pb37的熔点是183C,SAC305是217C)，所以就常会用到BiSn锡铋合金。或是分温度层(step soldering)焊接，也会用到这种低温合金。 锡铋这两种金属的价格虽然随着市场大宗商品价格的变动有些变动，但是和贵金属金银等相比，价格还算可以。

铋是一种很脆的金属，所以锡铋BiSn的韧性不够。但是如果加上1%的银，Bi57Sn42Ag1，就可以大大提高合金的柔软性和韧性了。

Cheers!



Pic: Google Image

PS: 上周我给加拿大的客户发邮件，不小心顺手写了祝感恩节快乐的语句。后来一点击发出后，就马上后悔了，因为我突然想起加拿大人感恩节不是在11月，而是在10月份。因为加拿大更加靠北边，他们的粮食收成季节早过美国，所以也提早庆祝感恩节…好在其中一个加拿大客户还挺幽默的，马上回复了我的邮件，祝我们这里感恩节快乐

Here is a list of tricks to help you overcome the issues that can arise while hand soldering silicon-based solar cells (and other applications as well). Some of these ideas are obvious for most, but all the suggestions can help you form a better solder joint - and build a better final product:

1)    Use the correct soldering tip. I’ve made the mistake of using an inappropriate solder tip before, and so have many of my customers. It’s a frustrating problem you will only let happen to you once: everything is set up perfectly but nothing will melt, until you notice the solder tip is not the correct size or shape. This has happened to many of my customers who were initially using cone point soldering tips when they were working with 2mm wide solder coated tabbing ribbon. Simply changing the tip to a 2mm wide chisel point made all the difference, and promoted soldering readily. Why such a big difference in performance? The chisel tip allows heat to flow across the ribbon, instead of only heating a single point. More heat flow = more heat in your solder joint.

2)    Pre-tin the soldering iron. Just as an appropriately sized soldering tip will distribute heat across the soldering surface, a bit of molten alloy can help create a thermal interface to maximize heat transfer. Remember to melt a small amount of solder onto the tip of your iron before soldering, and be sure it’s the same alloy you are soldering with. (Leave the custom alloying to us ;)

3)    Consider the alloy you are soldering. All the heat your typical soldering iron can produce will not be enough to melt some of the highest temperature alloys. Be sure to have a good understanding of the alloy you have selected. In some cases with low-temperature alloys (like bismuth or indium alloys), excessive soldering temperature can de-wet the alloy and char low temperature fluxes.

4)    Use the correct flux. Fluxes are quite different, I’ve spent my entire soldering career trying to get that point across. There are fluxes for high temperatures or low temperatures, cleaning with water or not cleaning at all. There are specialty fluxes for specialty alloys and there are fluxes for different soldering surfaces. Use the correct flux. If you don’t know what the best flux for the application is - just ask; that’s what I am here for.

5)    Use a bottom side heater. Silicon is known to pull heat away – that c-Si solar cell that needs to be soldered is a heatsink! Some solder equipment vendors also provide underside heating pads to help prevent excessive heat loss.

6)    Keep your soldering iron clean. That black crud that builds up on your soldering iron tip, it’s not helping you form a good solder joint. Those oxides and charred flux residues can easily be removed by wiping the hot iron across the wet sponge (that should be at your soldering station). A clean tip will lead to better heat transfer, and it will make the fluxes you use more effective.

This is the soldering station I use, it’s a PS-900 supplied by OK International. Just about any soldering iron will work, but they won’t all work as well – or come with as good support.

I’m still learning all the tricks to hand soldering, so feel free to share any you have learned over the years!

~Jim

Folks,

I have occasionally written on calculating solder alloy density, as there is surprisingly more interest than I thought there would be in this topic. Recently, it occurred to me that it might be beneficial to compare the calculated densities to actual densities of a few alloys to see how accurate the correct formula is (for the derivation of the correct formula see below). The formula assumes “perfect mixing” (i.e. no interactions between the alloy elements). The alloys we investigated were tin-bismuth-silver, tin-silver, tin and tin-bismuth.

To measure the density, I obtained a few alloys from Indium Corporation. My student, Evan Zeitchik, determined that a good technique to measure density is to machine the alloy into a rectangular parallelepiped (see photo), weigh it, and calculate its volume from its dimensions.  The results agree with the correct formula to about 1 to 2 %. Some people would ask why there is any difference. The reason is that all alloys form different phases, and some form intermetallics. These phases and intermetallics would typically have different densities than that calculated for the alloy. I will have more detail on this work in a future post. 

Here is a derivation of the correct density formula:

Many people incorrectly assume that if you have an alloy of x % tin and y % silver, that the density of this alloy would be 0.x*Density tin +0.y*Density silver. This intuitive linear formula is incorrect however, as density has two units (mass and volume).  An easy way to understand the derivation of the correct formula (proposed by Indium Corporation engineer Bob Jarrett) is to consider a 96% tin, 4 % silver example.

Lets assume I have 1 g of this alloy, 0.96 g is tin and 0.04 g is silver.

The volume of the tin is 0.96 g/7.31g/cc = 0.131327cc

The volume of the silver is 0.04g/10.5g/cc = 0.00381cc

So 1 g of the alloy has a volume of 0.131327 + 0.00381 cc = 0.135137 cc

Hence it's density is 1g/0.135137cc = 7.39989g/cc

Hence, the general formula is:

1/Da = x/D1 + y/D2 + z/D3

Da = density of final alloy

D1 = density of metal 1, x = mass fraction of metal 1

same for metals 2, 3

The formula continues for more than 3 metals.

I have developed an Excel spreadsheet that calculates density automatically. If anyone wants a copy, send me an email at rlasky@indium.com

Based on a recent post I published regarding the use of bismuth (Bi) in solder alloys, John writes:

"If Bismuth comes from the production of Pb, and if the use of Pb is being reduced, won’t the availability of Bi be reduced…and the price would increase?"

"Just thinking…"

Dr. Ron responds:

Lead has been banned from many of its original uses, paints, solders, water pipes, gasoline, etc. However, its increased use in batteries has actually caused lead consumption to rise. The USGS estimates that 88% of lead produced is used for lead-acid batteries.

Many of us, in electronics assembly, have been focused on the 2006 RoHS lead ban. This may have caused us to believe that lead use in electronics was significant. About 9 million metric tons (MT) of lead are consumed each year, only about 20K metric tons were used for solders prior to July 2006, this amount is only about 0.22% of the total. Electronic lead use being so small, is likely why the lead industry had little visibility in fighting RoHS. Their important customers were making batteries.

Lead is quite effectively re-cycled, as about 60% of the 9 million MTs/yr are from recycling and 40% from mining.

Over 100 million lead-acid auto batteries are sold each year in the US alone. In addition, the use of lead-acid batteries in fork-lifts, electronic vehicles, and golf carts has increased demand for lead. So, the bottom line is that lead use is expected to grow at about 2% per year.

Considering that we calculated that bismuth use in solders would be at most 5% of total bismuth production, it is unlikely that this use, or lead production reduction, would affect bismuth supplies.

Folks,

 A few people asked some questions after my last post on bismuth solders. Here they are:

1.      The low melting point of these solders is encouraging. What are realistic field use conditions?

Bismuth solders tend to be brittle, so drop shock environments such as mobile phones would not be recommended. However, thermal cycle performance from 0 to 100C is good, so stationary office equipment, televisions, desktop computers, etc may be good candidates.

2.     I am working with your colleagues on an automotive application and I am curious whether you have any idea how this alloy will perform between -40 and 0°C? We have not been reviewing bismuth-containing alloys due to their lower sheer strength, but may need to look at them in the future.

We can find no information on thermal cycle performance at these low temperatures.

3.     I hear that bismuth is rarer than silver, if we start using bismuth in solders couldn’t that make it very expensive.

An old number from Prismark puts the world solder use at about 50,000 metric tons (MT) per year.  Assume bismuth solders took a 5% market share (I think this would be the highest) that is 2,500 MT of bismuth solder (Bi57Sn42Ag1) or 1,425 MT of bismuth.

Although bismuth's occurrence in the earth's crust is 0.009 ppm (silver is 0.075 and gold 0.004 ppm), about 22,000 MT are produced each year.  In comparison, about 2,000 MT of gold, 20,000 MT of silver, 400 MT of indium and 5 MT of rhodium are produced each year.  In comparison to more common metals, total lead production is 8,000,000 MT/year and tin a little less than 700,000 MT.

 Realistically, it would seem to me to be unlikely that use of bismuth in solder, at 1,425MT/year out of 22,000 MTs,  would affect the price much, especially if the adaptation rate is more like 1-3%, instead of 5%. 

For those interested in how bismuth is produced, this Wikipedia quote may be of interest:

"According to the United States Geological Survey, world 2009 mine production of bismuth was 7,300 tonnes, with the major contributions from China (4,500 tonnes), Mexico (1,200 tonnes) and Peru (960 tonnes).^[11] World 2008 bismuth refinery production was 15,000 tonnes, of which China produced 78%, Mexico 8% and Belgium 5%.^[9]

The difference between world bismuth mine production and refinery production reflects bismuth's status as a byproduct metal. Bismuth travels in crude lead bullion (which can contain up to 10% bismuth) through several stages of refining, until it is removed by the Kroll-Betterton process or the Betts process. The Kroll-Betterton process uses a pyrometallurgical separation from molten lead of calcium-magnesium-bismuth drosses containing associated metals (silver, gold, zinc, some lead, copper, tellurium, and arsenic), which are removed by various fluxes and treatments to give high-purity bismuth metal (over 99% Bi). The Betts process takes cast anodes of lead bullion and electrolyzes them in a lead fluorosilicate-hydrofluorosilicic acid electrolyte to yield a pure lead cathode and an anode slime containing bismuth. Bismuth will behave similarly with another of its major metals, copper. Thus world bismuth production from refineries is a more complete and reliable statistic."

So I don't think bismuth supply and price would be affected by its use in solders.

Folks,

When the industry was preparing to transition to lead-free solders almost ten years ago (can it have been that long), tin-bismuth solders were serious candidates. Their low melting point, of about 138C, made these solders interesting candidates to replace tin-lead solder. However, if contaminated with lead, tin-bismuth solders can produce a eutectic phase that melts at 96C. In such situations the resulting solder joint exhibits poor performance in thermal cycle testing. Since early in the transition to lead-free solders it was expected that there would be numerous components and PWBs with lead-based surface finishes, this property made tin-bismuth solders unacceptable.

Another aspect of tin-bismuth solders is that they expand on cooling. This phenomenon can result in fillet lift in through-hole solder joints.

However, as we are now well into 2011, almost no components or PWBs have lead-containing finishes and many portable electronic devices have no through-hole components, so it may be time to reconsider tin-bismuth for some applications.

Some years ago, Hewlett Packard (HP) had performed work to show that adding 1% silver to tin-bismuth solder enabled this alloy to outperform eutectic tin-lead solder in 0 to 100C thermal cycle testing. Even at these low reflow temperatures, HP demonstrated solder joint strength with SAC BGA solder balls that was 65% that of tin-lead solder. Expanding on this work, Indium Corporation's Ed Briggs and Brook Sandy performed stencil printing and reflow experiments consistent with the requirements of current miniaturized components using this 57Bi-42Sn-1Ag solder. All of their results were promising. Ed presented a paper at SMTA Toronto,summarized the Hewlett Packard work, and reviewed the results of this new work.

So for applications consistent with 0-100C thermal cycling, 57Bi-42Sn-1Ag solder may be something to consider if the high temperature of SAC solder paste is an issue to components or PWBs in a product

Cheers,

Dr. Ron 

PS: Read my follow-on posting about bismuth.

Folks,

Many people responded to my recent post, In Search of Tin Whisker Fails in Lead-Free Soldering.  A few pointed out that the recent NASA report on the Toyota Unintended Acceleration Issue  discussed numerous tin whiskers that were found, one implicated in a failure.  The tin whiskers were emanating from tin plating.

We don't know, however, if tin whisker mitigation techniques were used. In a mission critical application, such as this, it would appear unwise to use RoHS-compliant electronics, especially since they are not required for automobiles.  In other words, autos are exempt from RoHS.  Let me be very clear, from a tin whisker perspective, I am uncomfortable with RoHS-compliant tin plating in mission critical applications.  Much more work needs to be done before such tin plating should be used in mission critical applications.

In addition, in response to my post, a number of people pointed out the difficulty of proving a tin whisker fail and the reluctance of any manufacturer to admit that their products had them.

But my quest remains unfulfilled; the question remains:

"... who knows of any verified tin whisker fails when tin whisker mitigation techniques where used? Tin whisker mitigation techniques typically use 2% bismuth or antimony in the tin, assure that the tin has a matte finish and use a nickel strike plating between the copper and the tin to minimize copper diffusion into the tin."

Restated, here is my point.  Since RoHS, quite a few people take a position something like this:

With RoHS-compliant assembly, even the world of non-mission critical electronics is at considerable risk of numerous catastrophic failures, due to tin whiskers, that will cost $100s billions.

I still maintain, that with mitigation techniques, such as recommended by iNEMI, tin whisker control, for non-critical electronics, can be manageable.

As I pack up to leave my office today at Thayer Engineering School at Dartmouth, I am across the aisle from the chaps that provide our computers and IT support.  They buy millions of dollars of electronics a year.  In chatting with them they state two things:

1. They have noted no difference in electronics reliability since RoHS implementation

2. On the very rare occasion that they get an electronics failure, it is almost always a hard drive.

Bottom line: Except for hard drives, modern electronics are very reliable for their use life.

I expect my quest will uncover some tin whisker fails, even with mitigation, but the fails will most likely be isolated and not a significant threat to the industry at large.

Cheers,

Dr. Ron

The image is from Dr. Henning Leidecker of NASA, one of the world's leading tin whisker experts.

Folks,

In a recent post, I shared my perspective on the pluses, minuses and neutral aspects of lead-free solder assembly. In the minus category, I listed tin whiskers. A few people commented that tin whiskers were the biggest concern in lead-free assembly. I have trouble understanding this perspective. I’m not saying these folks are wrong, just that I don’t understand their viewpoint.

First, let me say that I appreciate the concern for tin whiskers in mission critical electronics such as military, aerospace and medical. I am also sympathetic to the fact that, even though these types of electronics are exempt from RoHS, they may have to use RoHS compliant products because non-RoHS compliant products may not be available.

When I discuss the topic of tin whiskers, people will point me to NASA’s tin whisker failures website . However, when one goes to the site, there are only about twenty tin whisker fails referenced, many due to bright tin plate. Bright tin plate should never be used in mission critical electronics as it is virtually assured of producing tin whiskers. In addition, many of the articles referenced do not talk about tin whisker fails. Few if any fails are discussed relevant to RoHS (i.e. almost all fails discussed are prior to July 2006.)

I do not want to minimize the significance of tin whisker fails, some of them cost 100s of millions of dollars (e.g. satellite failures). In addition, there have been a few papers that have discussed the formation of tin whiskers even if mitigation techniques are used. Tin whiskers clearly can cause problems, but do not appear to be common, especially if mitigation techniques are used.

So here is my question, who knows of any verified tin whisker fails when tin whisker mitigation techniques where used? Tin whisker mitigation techniques typically use 2% bismuth or antimony in the tin, assure that the tin has a matte finish and use a nickel strike plating between the copper and the tin to minimize copper diffusion into the tin.

Surely if tin whiskers are a major concern, there should be many fails in the over $3 trillion worth of RoHS compliant electronics manufactured since July 2006.

Jon major recently joined the Indium Corporation as a Product Manager for Solar back-end assembly products. I greeted him with this impromptu interview.

Jim: First of all Jon, welcome. It’s great to have you as a new addition to the team!

Jon: Thank you Jim – it’s an exciting time to be at Indium Corporation and a fantastic time to be a part of the growing solar industry. I am extremely enthusiastic about my new position and am looking forward to making a positive contribution to the solar industry.

Jim: I noticed it didn’t take you long to get up to speed. Your time in Silicon Valley must have helped.

Jon: Coming from the electronics industry with a focus on product development, new product introduction, manufacturing, and external partner management, I am excited that my past experiences can contribute both to the industry and to Indium Corporation. After joining Indium only a few weeks ago, not only am I getting used to Upstate NY weather, but I have been immersing myself in solar with the goal of gaining a comprehensive understanding of:

•       Both rigid and thin-film technologies

•       Technology trends

•       Global and regional markets (EU, China, US, North America)

•       Solar supply chain (Silicon, wafers, cells, module, equipment, inverters, integrators)

•       Equipment manufacturers, contract manufacturers, and how we can collaborate with them to move the industry forward

•       Our products and pricing

•       Our current and future customers

•       Our short and long term opportunities

•       Our competition

•       Our roadmap

•       Our strengths, weaknesses, and threats

•       Our manufacturing capabilities and our QA process

•       Our sales channels, value proposition, key differentiators

•       All Indium processes

Jim: I know you've got solar products on your mind. Let our readers know a little bit more about your role here at Indium?

Jon: As a Solar Backend Product Manager I will focus (officially) on the business development and growth of Indium’s Solar Back End product offerings.  Now that sounds great but what does it actually mean? I could cut and paste my official job description but I prefer to explain it in my own words. As I think about the first part of that statement, “business development and growth…”, I see my role as:

–      Know the market, the customers, the product, and the competition

–      Develop relationships with the Indium team, reps, partners, equipment manufacturers, and, of course, customers

–      Write valuable data sheets, publications, and sales literature

–      Listen to our customers' needs and provide solutions

–      Manage schedules and orders with minimal surprises

–      Build cross-functional collaboration (sales, distribution, marketing, engineering, R&D, QA, production, management)

–      Never let down partners or customers

–      Support all functions of the organization, both internal and external

–      Deliver above & beyond commitments

–      Make great bets – on technology, customers, and opportunities

–      Understand the product life-cycle

–      Ship high quality, consistent product

The second part of that statement “..of Indium’s Solar Back End product offerings” is fairly straightforward. Of course this means I will focus on Indium’s current back end products (tabbing ribbon, bus ribbon, metallization paste (or as I prefer to call it – “grid ink”), flux and flux cored wire). With a product development background, this also means I have an opportunity to work with customers, partners, and R&D to develop and bring new products to market that will advance the module assembly industry – very exciting for me personally.

Ultimately, I think of my role as both building awareness of Indium’s products and superior technical support available to our customers as well as helping to shape our growing industry.

Jim: Okay Jon, you’ve had a while to settle in and get familiar with our Solar Team’s past and present – what are you planning for the future of module assembly?

Jon: Regarding the future of module assembly it’s a bit early to know for sure but I am excited about our low-temperature bismuth-containing alloys. These low temperature, lead-free, bismuth-containing alloys reduce the soldering process temperatures, thus reducing thermal stresses. I’m also working with the Indium production team to further reduce our tabbing and bus ribbon yield strength. A lower yield strength will reduce mechanical stress on cells during the assembly process. This is crucial to minimizing the possibility of microcracks and cell breakage during the solar module assembly process.

In closing, having lived in California for the last 10 years, I am not 100% familiar with our Upstate New York climate, and especially not all the snow shoveling. I see in my future a solar powered driveway heater!

Jon can be reached at jmajor@indium.com

Although most scientists today feel that alchemy has been widely discredited, and I have been taught to agree, the idea of it is whimsical and exhilarating.  Of course, I don’t have a hope of changing the makeup of bismuth or transforming it into another metal, but in a modern way, it’s very interesting how bismuth can be used to change the properties of other metals significantly - through alloying. In my last post on bismuth, I outlined its physical properties, some of which I find rather unusual. The main reason I originally researched bismuth was because of its viability for use as a low temperature Pb-free alloy.

BACKGROUND:
I'm not an alchemist like Newton, I can't transmute bismuth to gold like Seaborg, but I can use bismuth and metallurgy to transform an alloy.

I just read a fascinating article about Sir Isaac Newton titled, “Moonlighting as a Conjurer of Chemicals”. Newton is widely regarded as one of the most important people in the history of science, and he was very devoted to his work. The revelation in this article about the depth of his interest in alchemy left me somewhat awestruck. In my previous reading about Newton, I remember perhaps a mention of his interest in alchemy, but I guess I figured it was because science and alchemy, at that time, were fairly closely related. As scholars are starting to translate more of his diaries, they are discovering that his passion was alchemy and he saw it as the path to complete control over the natural world.  

I suppose if it was still socially acceptable to be an alchemist that is what I would have wanted to be; it just never seemed to be a viable option. What I have chosen to do now kind of makes sense considering chemistry/metallurgy is about as close as you can get nowadays. 

Reading this article reminded me of some interesting information I had come across while researching bismuth a couple months ago; namely that, although bismuth wasn’t one of the seven central metals in alchemy, it has an "alchemical" symbol (#52 in the image to the left) and was frequently used, although it’s not known for what purpose. I also came across this bit of information:

“In 1980, a scientist named Glenn T. Seaborg was able to transmute a minute quantity of bismuth into gold at the Lawrence Berkeley Laboratory, via nuclear collisions.” 

Seaborg is a fascinating scientist in his own right and discussion about him could fill quite a number of blog posts. Is it possible that alchemists underestimated bismuth and should have focused more on turning it into gold?

BACK TO MODERN TECHNOLOGY:
The eutectic alloy of 58Bi/42Sn has been used since the Pb-free transition as a low temperature (138°C liquidus) option for soldering products used at ambient temperatures - such as consumer electronics.  Note the low melting temperature of this alloy, despite the individual melting temperatures of bismuth and tin, 271°C and 232°C, respectively. Although bismuth is typically known to be quite brittle, this alloy has been shown to perform similarly to the SnPb eutectic solder (in response to a comment on my last post, for further data-based information, please feel free to contact me directly). In cases where more ductility is desirable, 1% silver can be added, further improving thermal shock and fatigue resistance. Perhaps the similarity in performance makes sense because of bismuth’s proximity (right next to) lead on the periodic table, although they differ in several other qualities such as toxicity.

The more I learn about bismuth, the more interested I become. Now if only I could find some in-depth alchemical information about it from Sir Isaac Newton.

Folks,

Answers to the quiz of a few weeks back......

Phil and Rob had agreed to ask the GM if it was OK to ask the tech and engineers at some of their subcontractors to take the test anonymously. Over a period of two months Phil and Rob got 52 people to agree, almost all of them after Phil or Rob agreed to take them to lunch. They asked Patty to grade the “exams.” Today Patty would reveal the results.

“Phil, this is one of the best bets I have ever made,” teased Rob.

Everyone at the lunch table chuckled, but the look on Phil’s face said he expected to lose. Rob has said that he thought the average score would be less than 70%, Phil insisted that it would be greater than 85%. In asking the different folks to take the test, invariably Phil started asking questions not on the test. He was surprised that no one knew what tin pest was. He even asked how to time balance a chip shooter and flexible placer, only one in twenty knew.

As Patty approached the lunch table, the ensemble held their breath.

“OK, Patty, tell us the bad news,” Phil said in a resigned tone.

“Rob wins, the average score was 58%,” Patty said getting to the point. “Here are the answers and percentages on each problem,” she went on:

1.    What is the composition of SAC305?
96.5% tin, 3.0% silver, 0.5% copper. 60% got this right.

2.     What are tin whiskers?
Tin whiskers are metal whiskers that can “grow” from tin plating on component leads. They are mitigated by 2% bismuth in the tin, a nickel overplate of the lead copper, a matte tin finish, and a few other mitigation approaches. 40%.

3.     In a stencil aperture, what is the area ratio?
The ratio of the area of the aperture opening divided by the area of the side walls. This ratio is typically used for circular and square apertures. It is equal to D/4t, where D is the diameter of square side and t is the stencil thickness. 40%

4.    What is an approximate peak temperature for a reflow oven in lead-free assembly?
Any answer 235 to 250C accepted. 90%

5.     A board is inspected after wave soldering and one lead is not soldered to the board. The board is run through the wave solder machine again and has the same defect on the same lead. What is the most likely cause of the defect?

a.       The solder temperature is too low.

b.      The pad on the board is oxidized.

c.       The preheat temperature is too high.
b 70%

6.     What are local fiducials on a PWB for?
Local fiducials are located near the pads of a component with fine lead spacings to assure accurate placement. 70%

7.     What does "thixotropic" mean in regard to solder pastes?
The viscosity decreases with increasing shear stress. Hence, during printing the viscosity drops as the paste is forced through the aperture, aiding good aperture fill. It increases as the printed deposit rests, minimizing slump. 20%

8.     A chip shooter places passives at a rate of 36,000 per hour. It is placing 300 passives on a PWB, how many seconds will the chipshooter take to place the passives on one board?
300/36000 = 1/120 hr = 30 seconds. 90%

9.     A reflow oven belt speed is 100 cm/min. The PWB is 40 cm long. What is the minimum cycle time that the oven can support?
The amount of time that the belt needs to cover 40 cm is 40/100 = 0.4 minutes = 24 seconds. This is the minimum cycle time the oven can support. 40%

10.   What is "tombstoning"?
Tombstoning is observed when a passive component's terminations experience unequal wetting forces which are strong enough to lift one end of the passive so that it looks like a tombstone. 60%

Overall average score 58%.

“Wait a minute Patty, your answers are too demanding,” Phil shouted.

“Calm down Phil, I gave full credit for anything close,” Patty responded.

In unison, almost everyone at the table sighed “Yikes.”

Patty interjected, “One person who received a 70% commented after completing problem 9, ‘I didn’t think I would need a PhD in math to do this quiz.’ “

All agreed that organizations like the SMTA and IPC were more needed than ever.

在中國，現在還是厚膜太陽能光伏技術佔主導(Thick Film Solar PV)。所以，Indium公司相對成熟的太陽能產品中，也就是鍍錫銅帶（Tabbing Ribbon or Bus Ribbon）的生意機會比較多了。 

镀锡铜带是韌銅，單面或是雙面再鍍上一層含錫的合金薄層，用於焊接。常用的鍍錫層有：

• Sn63 Pb37
• Sn96.5 Ag3.5
• Bi46 Sn34 Pb20
• Bi58 Sn42
• Bi57 Sn42 Ag1

含有鉍(Bismuth Bi)鍍層的銅帶，適用于對高溫比較敏感的光伏太陽能板子的硬化，特別是薄膜技術的板子。



Video: Youtube

This blog has been in existence for a little over two years now, and we would like to thank our readers for the feedback and inquiries you have provided. I welcome your comments on what you would like from us. Leave a comment below, or email me at jhisert@indium.com.

And now a look back on past topics of interest:
 

Grid Ink, Silver Ink, Conductive Ink

Bismuth/Tin Tabbing Ribbon, A Low Temperature Pb-Free Alternative

Plated Metallization for C-Si Solar Cells

Increase Packing Density for Evaporation Crucibles

Photon’s 5th PV Tech Show 2010 USA

IPC Solar Standards Update

Solder Shelf Life as Explained by Eric Bastow

Tips to Speed Your Solder and Flux Selection

What's Happening in the Technical Service Department 

A Day in the Life of a Tech Guy

A Clean Laboratory

CIGS for Beginners

3rd Renewable Energy Expo 2009 in New Delhi, India

Solar Products and Representatives

Kleenex®, Google™, FedX®, CIGs?

Indium Solar Products Reunited

Trade Show Visitors Love the Ground Floor

Solar Product Data Sheets

Intersolar 2009 – What Barrier to CIGS Technology?

Concentrator Photovoltaic Systems - Will they reach 50% Efficiency?

Standards for Solar Panel Manufacturing

Solar Panel Certification: “Barrier and Benefit” Reviewed by Eric Bastow

Low Temperature Metallization Paste

What Will Your Interest Be At InterSolar? Meet the Bloggers And Let Us Know.

Share Your Solar Images

SAC vs. Sn/Ag for Solar Soldering

Solder Thickness for PV Interconnect

What is Bus Ribbon?

Standard PV Interconnect Ribbon Sizes

No-Clean Flux

Photovoltaics in EMS Sector

PV Interconnect Products

Eric Bastow - East Coast Technical Support

Mario Scalzo - West Coast Technical Support

Au/Sn Sputtering Targets

SMT Goes Solar

A Trip Down Memory Lane 

More Information About Metallization Paste

A year in the Life of a Solar Blog

CIG Target

23rd European Photovoltaic Solar Energy Conference and Exhibition

TCO choices for CIGS manufacturing 

CIGS Absorber Layer Electroplating

No Slump Metallization Paste

Meet the Bloggers

CIGS - Can sputtering make a breakthrough?

Fluxes for Soldering Tabbing Ribbon

Computer Brain vs. Solar Photovoltaic

Beam it down from space

Selection of the Optimum Lead-Free Solder for Solar Tabbing Ribbon

Record Makes Thin-Film Solar Cell Competitive with Silicon Efficiency

Why Thin-Film Solar Cells are Here to Stay

Hot Rooftops to Flashy Digital Cameras

Synchronize Your Solar Cell

Solar Conversion Efficiencies  

Government Support is the Key

It's Just a Beginning ...

Okay, I have a confession to make: I’ve always had a grudge against bismuth, ever since I started recommending thermal interface materials. It is the polar opposite of my favorite element (indium) – well, as much as a metal can be. These 2 elements (indium or bismuth) are added to almost every solder with a lower solidus temperature than Sn/Pb. The choice for most thermal interface applications that I have dealt with was indium or an indium alloy, but now I am starting to become very fond of my new friend bismuth for solar applications.

Bi/Sn and Bi/Sn/Ag are now available as a solderable coating for our Tabbing and Bus Ribbon. After getting a feel for this material, I must say I find it pretty nice to work with. Both alloys melt at 138-139degC, with the Bi/Sn/Ag having a greater tensile strength (which is not necessarily a good thing for tabbing ribbon). With a little bit of lab time I have isolated an existing flux that works very well with these alloys. So far GS-5454 has formed good solder bonds down to 160degC. This is great news, because it allows you to minimize the reflow temperature (and stresses) of your C-Si/tabbing ribbon interface. 

~Jim

Considering a fusible alloy as a solution really starts with the applications temperature profile. When cooking a turkey (pop-up timer) or supressing a fire (sprinkler systems), its all about the heat and what the fusible alloy does in response to it.  Reliability is achieved through ensuring that each alloy is homogenious and not subjected to segregation. Take a look at our list of alloys, and you'll find that there are many options to choose from, many of which are Bismuth containing. These can be manufactured in many shapes and sizes and due to the high volume nature of these applications, the need for tape and reel is almost a given.
 

The binary eutectic alloy of bismuth and tin (Bi/Sn) is well suited for many low temperature applications due to its melting point of 138°C, but the alloy is known for being rather brittle for a solder alloy.
All hope is not lost though - there is a similar alloy, known as Indalloy 282, which drastically reduces the brittle nature of the Bi/Sn alloy with the addition of just 1% Silver (Ag).  This 57%Bi/42%Sn/1%Ag alloy has a 1°C higher melting point.  Although you won’t be able to notice this reflow change, you will immediately notice the physical difference if you compare solder wire made from each alloy.  The Bi/Sn wire is likely to break upon bending, unlike the Bi/Sn/Ag alloy.
The easiest (and most economical) way to experiment with these alloys is with a solder wire kit . With a wire kit you can obtain both wires in the same diameter, and you get 5 fluxes to help with soldering.  You can also get up to 10 different alloys if you want to experiment-your-heart-out and compare Bi/Sn and Bi/Sn/Ag to other alloys like Sn/Pb or Sn/Ag/Cu.

While it's not the typical material of choice for thermal applications, bismuth alloys have found their place in this market with some unusual product designs.  For this reason, we have decided to highlight this unique material.   Check out the new bismuth website and hopefully learn a few things about these low temperature solders.